CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: CaptainZoop

Page 1 of 3 1 2 3

Search Forums: Search took 0.01 seconds.

  1. Replies
    2
    Views
    479

    What rigid ironhead oil tank is this?

    I have had one of these in the past but never learned who made it. I want to buy another for a project but can't seem to find any information or pictures of them. These photos are of the one off my...
  2. Replies
    1
    Views
    253

    Ironhead clamp riser question

    Has anybody cut bars in half to fit into the single piece clamp risers that old ironheads use? Normally they run a two-piece bar with internal wiring but I would like to run a one-piece ape hanger....
  3. Replies
    9
    Views
    1,632

    the stock kickstand off which bike? i have a...

    the stock kickstand off which bike? i have a sportster kickstand here and it requires two tabs to mount, but the frame only has one.

    I'm finding it hard to believe that I'm the only one asking...
  4. Replies
    20
    Views
    2,105

    Thank you again, this is perfect. And yes,...

    Thank you again, this is perfect.

    And yes, I've been chasing this problem for quite some time. Haha. Cheers
  5. Replies
    9
    Views
    1,632

    bump

    bump
  6. Replies
    20
    Views
    2,105

    This is what I was looking for, thank you. So...

    This is what I was looking for, thank you.

    So now my question is, if I get the
    Timken bearing cone #07087, which neck cups do I need to get to go with it? My paughco frame (s120e) does not have...
  7. Replies
    20
    Views
    2,105

    7/8 to 1 inch neck cup conversion

    I have a 7/8 stem on a springer that I want to run on a sportster paughco frame that has a 1inch neck. im looking for a conversion kit for the job but when I search online i can only find a...
  8. Replies
    6
    Views
    1,369

    much appreciated!

    much appreciated!
  9. Replies
    6
    Views
    1,369

    Piston installation

    I'm installing a 1200 kit on a 96 883 sportster. The pistons are reverse domed made by Sifton but are unmarked as to which way they should be facing when installed. the only noticable difference in...
  10. Replies
    11
    Views
    637

    Any of them show up as "bad" as the one in my...

    Any of them show up as "bad" as the one in my photo? I'm in Portland right now and haven't seen the sun in like 3 weeks... blow dryer maybe? Haha. I dont wanna strip the thing again since I wont be...
  11. Replies
    11
    Views
    637

    Tire has curve in it

    I just built this rear wheel for my sporty and the tire has this crazy curve in it. The rim is trued fine and I even tried running it with 20 psi to try to get it to work itself out but that didnt...
  12. Replies
    8
    Views
    992

    Ha, that's brilliant. Might try the spoon. Thanks

    Ha, that's brilliant. Might try the spoon. Thanks
  13. Replies
    8
    Views
    992

    Thanks for the info everyone. Looks like the rods...

    Thanks for the info everyone. Looks like the rods are too big. They're the S&S adjustables for hydraulic. I have the S&S hydraulic to solid lifter kit installed so maybe thats why they don't fit....
  14. Replies
    8
    Views
    992

    Installing pushrods

    I'm trying to install the pushrods on a shovelhead motor but I have a problem. With the tappets at their lowest and the rod fully compressed it wont fit into the recess. I stuck my finger into the...
  15. Replies
    5
    Views
    523

    Thank you, will do

    Thank you, will do
  16. Replies
    5
    Views
    523

    The problem is I dont know what to type into the...

    The problem is I dont know what to type into the search on ebay to find one. Ive tried all sorts of variations of words, a part number would solve everything. I'm not very adept at this kind of...
  17. Replies
    5
    Views
    523

    67-72 backing plate nut

    Does anybody know the part # for the nut that holds the backing plate to the frame on a 67-72 hydraulic brake drum? Or does anyone know what size/thread it is? My guess is a 5/8-20 but none of my...
  18. Replies
    6
    Views
    1,321

    Thanks, will do

    Thanks, will do
  19. Replies
    6
    Views
    1,321

    Used a veneer, albeit a shitty plastic one....

    Used a veneer, albeit a shitty plastic one. Measured stems and inside of neck.
  20. Replies
    6
    Views
    1,321

    Neck cups for Paughco frames

    I have two Paughco frames that I need neck cups for, one is a sportster the other a big twin.

    For the sportster frame i need a cup with an inner diameter of 1 inch and an outer diameter of...
  21. Replies
    13
    Views
    914

    thanks

    thanks
  22. Replies
    13
    Views
    914

    Brake line tee

    I'm setting up the brakes on my 82 shovel, rear juice only (67-72), and have an extra fitting in the brake line tee. Can I just put a bolt in there or will it mess up the system? I ordered the...
  23. Replies
    16
    Views
    1,028

    Post a picture then? :banghead:

    Post a picture then? :banghead:
  24. Replies
    16
    Views
    1,028

    Hey Tattooo, thanks for your input, but I believe...

    Hey Tattooo, thanks for your input, but I believe all I asked for was a diagram showing how the rear axle is installed.
  25. Replies
    16
    Views
    1,028

    no, it's a hydraulic drum. it only has one...

    no, it's a hydraulic drum. it only has one bearing in it though and there's room for at least another and a spacer...

    the right side spacer doesn't matter really, i'm going to shim it to fit. had...
Results 1 to 25 of 58
Page 1 of 3 1 2 3

Log in

Log in