CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: TriNortchopz

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.03 seconds.

  1. Replies
    17
    Views
    160

    relates to a saying I heard many years ago about...

    relates to a saying I heard many years ago about connecting booster cables...

    Positive is nothing without a ground.
  2. Replies
    41
    Views
    9,060

    but Scottie's ain't: 101388

    but Scottie's ain't:

    101388
  3. Replies
    17
    Views
    160

    Disconnect wires until it stops tripping the...

    Disconnect wires until it stops tripping the breaker...one at a time to trace it.

    I see your rectifier/regulator just hanging there...is it one of those units that needs the case to be grounded?
  4. Replies
    41
    Views
    9,060

    Good post Gary; been following CBH for years, and...

    Good post Gary; been following CBH for years, and also your posts over on Chopper Compendium...Welcome!
  5. Replies
    41
    Views
    9,060

    Were you able to get the correct clearance at...

    Were you able to get the correct clearance at each rocker pivot point (0.002"), not too tight and not to sloppy...

    and the shouldered bolts or rocker studs are a tight fit in the legs (holes all...
  6. Replies
    17
    Views
    160

    Got a multi-meter to check voltage, continuity...

    Got a multi-meter to check voltage, continuity and grounds?

    EVO: Electrical System
    FUSES, RELAYS, CHARGING SYSTEM

    "The Circuit Breakers (CB) used on Sportsters are of the self-resetting type....
  7. Replies
    17
    Views
    160

    What year is your machine? and what size...883? ...

    What year is your machine? and what size...883?

    Guessin' you've seen this thread:
    http://www.chopcult.com/forum/showthread.php?t=53520
  8. Replies
    42
    Views
    825

    I was thinkin' with that low compression, using a...

    I was thinkin' with that low compression, using a wheel roller to get the engine spinning faster than a kicker would help get it started...then a hill was mentioned^^^...
  9. ... Looks like that horrible human has lead the...

    ...
    Looks like that horrible human has lead the states to be #1 again!

    "The number of confirmed COVID-19 cases in the U.S. rose to 83,836 on Thursday — more than any other country, overtaking...
  10. Replies
    3
    Views
    105

    The master link is wider than the rest of the...

    The master link is wider than the rest of the chain; how much clearance between those pins and the lower frame rail?

    got enough clearance between the side of the tire and the chain?

    does your...
  11. Replies
    9
    Views
    249

    this is hand washing (gotta scroll down a couple...

    this is hand washing (gotta scroll down a couple of clips):

    https://mailchi.mp/homemadetools/5500-ton-crane-hook-foldown-wind-turbine-tower-baby-steam-locomotive-348843?e=d1cc252388
  12. Thread: Covid 19

    by TriNortchopz
    Replies
    73
    Views
    2,931

    I'll try again...ya gotta scroll down a couple...

    I'll try again...ya gotta scroll down a couple clips here

    good handwashing technique:
    ...
  13. Thread: Covid 19

    by TriNortchopz
    Replies
    73
    Views
    2,931

    Y'all heard about washing your hands to prevent...

    Y'all heard about washing your hands to prevent the spread...well here is a video showin' the right way:
    ...
  14. could have some green loctite in there, or just...

    could have some green loctite in there, or just corrosion...maybe a locking pin or setscrew from the side of the neck - did ya check for one of them? Then more heat, a long solid drift fitted in...
  15. Replies
    7
    Views
    220

    +1^^^,looks good, nice job on the pipes and all;...

    +1^^^,looks good, nice job on the pipes and all; the +6 with the z bars fits well
  16. Replies
    42
    Views
    825

    Stator is part of the charging circuit, not...

    Stator is part of the charging circuit, not ignition circuit.
    Disconnect the stator/regulator wire,ensure battery is fully charged,go through all steps identified by all above,then start it.
    ...
  17. Replies
    42
    Views
    825

    okay,my experience has been rough idle and major...

    okay,my experience has been rough idle and major breakup at load...verify by excessive arcing at points while running.
  18. Replies
    42
    Views
    825

    so not starting...got spark? with the key on and...

    so not starting...got spark? with the key on and points closed,open the points manually,plugs should spark...got spark? can always do a simple plug swap...just' cause they're new,don't mean they're...
  19. Thread: Covid 19

    by TriNortchopz
    Replies
    73
    Views
    2,931

    101008

    101008
  20. Replies
    24
    Views
    496

    seen this: Retro Tech – Installing A Morris...

    seen this:

    Retro Tech – Installing A Morris Magneto on a Shovelhead

    "As for those easy starts, modern Morris mags use Morris’ balanced impulse coupling system, which works with both kick and...
  21. .. Fake Bearings and Bearing Identification ...

    ..
    Fake Bearings and Bearing Identification

    Until talking to our Friends at ERIKS and TIMKEN in 2017, we had no idea just how widespread and serious the problem of counterfeit/fake bearings has...
  22. This may be a reference for you as you...

    This may be a reference for you as you build/rebuild your Ironheads:

    How to Build a Sportster
    (from a pile of junk) 7 chapters

    in Chapter 5; a short example of the type of info:

    "And now a...
  23. Replies
    4
    Views
    228

    looks like your fork tubes are 33mm: ...

    looks like your fork tubes are 33mm:

    https://www.dotheton.com/index.php?threads/fork-tube-diameters-list.20950/
  24. Replies
    4
    Views
    228

    This may be of interest; a guy choppin' his...

    This may be of interest; a guy choppin' his KZ440:

    Bacca's KZ440 Kawasaki

    "...Front footpegs going 7" forward and brake pedal going on old footpeg bolthole. Using old rearset gearshift turned...
  25. This may be helpful as you proceed: THREAD;...

    This may be helpful as you proceed:

    THREAD; 1982 Ironhead Transmission Removal (W/ Pics):

    http://xlforum.net/forums/showthread.php?t=2023217

    this may supplement your manual:
    1971 - 1985...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in