CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Nanonevol

Page 1 of 11 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    11
    Views
    157

    Yeah, I'm thinking of doing that or starting with...

    Yeah, I'm thinking of doing that or starting with a 3/4" bar and adding a shim or bushing, rather to make it fit 7/8" risers.
    I'll put up photos of the project when I get a minute.
  2. Replies
    11
    Views
    157

    Good ideas. I don't have tools to machine but...

    Good ideas. I don't have tools to machine but I'll get it done. Thanks.
  3. Replies
    11
    Views
    157

    Sorry I guess I'm being confusing. Photo might...

    Sorry I guess I'm being confusing. Photo might help.
    https://i.imgur.com/9GF9sCGl.jpg

    But, yeah I need risers that fit these odd 3/4" mounts and then standard 7/8" handlebars.
  4. Replies
    11
    Views
    157

    Thanks, yeah except that the mount on the fork...

    Thanks, yeah except that the mount on the fork trees is for 3/4" bars which are ​smaller than the typical 7/8" or 1" bars.
  5. Replies
    11
    Views
    157

    Buell Blast Bars

    I'm using a Blast fork on my Paugho 45" project and I need the risers which seem to fit a 3/4" bar . Been Goggling but can't find them anywhere.
  6. Replies
    4,272
    Views
    326,895

    http://youtu.be/y4sALru9IJk...

    http://youtu.be/y4sALru9IJk
    http://youtu.be/y4sALru9IJk
  7. Replies
    15
    Views
    665

    Watched some videos on bearing setup. Looks...

    Watched some videos on bearing setup.
    Looks like a special tool needed to remove the race.
    I may just take it to the local indy shop.
    Assume I'd need it out even with the sealed bearing mod.
  8. Replies
    15
    Views
    665

    Thanks again TriNortChopz, you're a Master! That...

    Thanks again TriNortChopz, you're a Master!
    That sealed bearing kit looks like the way to go. Much simpler and "modern".
  9. Replies
    15
    Views
    665

    Maybe I can get some advice about the rear wheel....

    Maybe I can get some advice about the rear wheel. First I thought I needed a pair of sealed bearings for a 3/4" axle and 1 3/4" bore
    but on closer inspection it looks like the wheel has outer...
  10. Replies
    30
    Views
    1,048

    Wow, Bono's jacket and Tom Petty's signed guitar....

    Wow, Bono's jacket and Tom Petty's signed guitar. Don't miss that!
  11. Replies
    15
    Views
    665

    Excellent advice as always,, however,,This...

    Excellent advice as always,, however,,This Sportster wheel isn't going to work for other reasons. I'm buying a Buell wheel with tire and rotor for $125 and think I can sell this for $250 so why not....
  12. Replies
    15
    Views
    665

    Oh, OK. Didn't know I could do that. But I'd...

    Oh, OK. Didn't know I could do that.
    But I'd need a seal that fits also.
  13. Replies
    15
    Views
    665

    The outer diameter needs to be 1 3/4" (44.45mm)...

    The outer diameter needs to be 1 3/4" (44.45mm) to fit the wheel.
    I think I have a metric/imperial mismatch problem here.
    Probably best to look for a Buell wheel.
    Will also need the brake...
  14. Replies
    15
    Views
    665

    I'm not finding anything that works. Maybe I...

    I'm not finding anything that works. Maybe I should look for another wheel?
  15. Replies
    15
    Views
    665

    Thanks! The axle is maybe metric as it is 17 mm....

    Thanks! The axle is maybe metric as it is 17 mm. The inner of bearing is .75" which is 19.05 mm. It's a tapered roller. I'll look for bearings.
    Sorry, what is "BCD"?
  16. Replies
    15
    Views
    665

    ID ths wheel?

    I'd like to fit this wheel on a Buell Blast fork I'm using on my Paugho 45" bike.
    Maybe I don't need to ID it to use it?
    The Buell axle is too thin for the wheels bearings. Just measure and shop...
  17. Replies
    107
    Views
    12,918

    Yeah, I was that kid too. Used to love taping up...

    Yeah, I was that kid too. Used to love taping up the bars with different kinds of tape.
    I lived on my bike. Thought it was my horse in a Western.
    https://i.imgur.com/tawnlATl.jpg
  18. Replies
    5,890
    Views
    3,511,646

    ​Ogle, ogle, ogle

    ​Ogle, ogle, ogle
  19. Thread: 41 el

    by Nanonevol
    Replies
    635
    Views
    20,635

    Epic! So it was more than just the intake leak?...

    Epic! So it was more than just the intake leak?
    "Toshi" didn't find the missing washer?
  20. Thread: 41 el

    by Nanonevol
    Replies
    635
    Views
    20,635

    I love it! When you were struggling with the bike...

    I love it! When you were struggling with the bike you took abuse from everyone.
    Now it's running right and its fuck em all!
  21. Thread: 41 el

    by Nanonevol
    Replies
    635
    Views
    20,635

    Curious as to what you had the head torqued at...

    Curious as to what you had the head torqued at and what it needed to be at.
  22. Replies
    12
    Views
    962

    https://greasykulture.com/magazine

    https://greasykulture.com/magazine
  23. Replies
    16
    Views
    1,239

    Now that I think of it--- That is a clean...

    Now that I think of it---
    That is a clean looking carb you pictured. I wonder if it is a "Premier" or a new Wassell Premier.
    If it is it will have a removable pilot jet on the opposite of the side...
  24. Replies
    16
    Views
    1,239

    Here's some cutaway photos. First one from...

    Here's some cutaway photos. First one from Bushmans, second from Vintage Bike
    https://i.imgur.com/mTw6Amdl.jpg
    https://i.imgur.com/H4XqQ17l.jpg
  25. Thread: 41 el

    by Nanonevol
    Replies
    635
    Views
    20,635

    You have to be more direct with Toady. Just tell...

    You have to be more direct with Toady. Just tell him to FUCK OFF!!!!!!
Results 1 to 25 of 272
Page 1 of 11 1 2 3 4

Log in

Log in