CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: drivermark

Page 1 of 3 1 2 3

Search Forums: Search took 0.01 seconds.

  1. Buy the CD/downloads, they're well worth the...

    Buy the CD/downloads, they're well worth the money.
    And you won't be disappointed.
  2. Replies
    21
    Views
    1,033

    That sounds like a helluva idea

    That sounds like a helluva idea
  3. Replies
    11
    Views
    263

    105360 Thank you guys for all the help. Went...

    105360

    Thank you guys for all the help. Went to the coast this last weekend so I missed the last few posts until today.
    The last snap here is how everything lined up just following the...
  4. Replies
    11
    Views
    263

    105288105289 Here's what I ended up with...

    105288105289

    Here's what I ended up with doing what Jim wrote.
  5. Replies
    11
    Views
    263

    Thank you so much for the quick replies. After...

    Thank you so much for the quick replies. After posting the original post I went back out to the shop and started checking on things.
    I put a straight edge on the rear sprocket. (stock wheel and...
  6. Replies
    11
    Views
    263

    Aligning drive train.

    What's the best way to align the drive train? I searched the TECH archives, all I could find on the subject was this thread.
    http://www.chopcult.com/forum/showthread.php?t=47373 which didn't...
  7. Replies
    15
    Views
    275

    105047105048 Got it all put back together...

    105047105048


    Got it all put back together today. here's the tranny and most of the hard parts that were replaced.
    I would like to thank JBinNC and Dragstews for all of your help.
    Gentlemen,...
  8. Replies
    15
    Views
    275

    I just checked that and it seems nice and tight,...

    I just checked that and it seems nice and tight, no slop.
    Thank you, I never would have thought of that.

    Can any one think of anything else I may have missed?
  9. Replies
    15
    Views
    275

    Whoops forgot to write that one down tolerance...

    Whoops forgot to write that one down tolerance .004-.015 actual .008


    And the bearings would be for the later rotary top what would that be? 82-86?

    Thanks again Jim

    Am I...
  10. Replies
    15
    Views
    275

    Thanks again gentlemen. While I'm at it...

    Thanks again gentlemen.

    While I'm at it here's a run down on the specs at assembly.

    spec. in manual actual...
  11. Replies
    15
    Views
    275

    Finally got to the point that I'm putting it back...

    Finally got to the point that I'm putting it back together and have a question. Is reaming the bushing on the main drive gear an absolute necessary? When fitting it together the gear slipped onto...
  12. Replies
    20
    Views
    442

    I just mount mine to the top of my work table w/...

    I just mount mine to the top of my work table w/ some 5/8 all thread and a couple blocks of plywood and 5/8 nuts. I use the all thread and a couple more blocks and nuts to clamp down the wheel/tire...
  13. Replies
    20
    Views
    442

    Learn how to DIY. and 1) You'll never have to...

    Learn how to DIY. and 1) You'll never have to look for someone to do it for you cheaply, and
    2) If you want you could be the guy charging to change tires.

    A tire changing "station" makes all the...
  14. Replies
    12
    Views
    317

    Very Nice

    Very Nice
  15. Replies
    15
    Views
    275

    Thanks, JB and Stews, that clears that up. The...

    Thanks, JB and Stews, that clears that up. The mention of a factory tool just had me wondering if the placement of the counter shaft bearings was more critical than it is.
  16. Replies
    15
    Views
    275

    Another thing I am curious about, the main drive...

    Another thing I am curious about, the main drive gear bushing. Another thing I was reading about in the old "Easyriders Tips and Tricks #4" (article starts on pg 63...
  17. Replies
    15
    Views
    275

    Thank you very much Jim.

    Thank you very much Jim.
  18. Replies
    15
    Views
    275

    Questions about 4 speed trans.

    As I'm sure some have figured out I am in the middle of fixing up the 4 speed in my '85 Softail.
    Reading thru the FSM about installing bearings in the counter shaft gear the manual indicated to use ...
  19. Replies
    27
    Views
    1,128

    Never seen one like that before , I'm used to the...

    Never seen one like that before , I'm used to the plastic P'sOS like from Office Supply.
    Very nice work Mr. Grub
  20. Replies
    12
    Views
    591

    And they cost more (which is probably why I've...

    And they cost more (which is probably why I've never even looked at one)
  21. Replies
    27
    Views
    1,128

    Please forgive my ignorance but... What is it?

    Please forgive my ignorance but... What is it?
  22. Replies
    27
    Views
    1,128

    Now that's spiffy!

    Now that's spiffy!
  23. Replies
    12
    Views
    591

    What's the deal with the O-ring chains? Are they...

    What's the deal with the O-ring chains? Are they bigger somehow (I've never looked at one)
  24. Replies
    12
    Views
    591

    I just happened to read in Easyriders Tips and...

    I just happened to read in Easyriders Tips and Tricks #1 an article about that (the chain chewing up the starter gear housing) called "How not to Score" you can find a PDF at the link below the...
  25. Replies
    27
    Views
    1,128

    That piece of plate that looks like aluminum with...

    That piece of plate that looks like aluminum with the what looks like a starter motor, is that a gizmo to bypass having to have a transmission to be able to start the test motor? If so how did that...
Results 1 to 25 of 71
Page 1 of 3 1 2 3

Log in

Log in