CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Down

Page 1 of 10 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    7
    Views
    536

    Looks like it's garage made to me. Those welds on...

    Looks like it's garage made to me. Those welds on the plates in the rear? Oof.
    Someone tried to build an FXR/Touring frame. It's probably fit for a rubber mounted Harley motor. Impossible to say...
  2. Replies
    4
    Views
    258

    Mr. Confab is right. I've disabled ABS on a few...

    Mr. Confab is right. I've disabled ABS on a few touring Harleys and it's as simple as pulling the fuse. You could remove all the ABS crap and leave the fuse out, your bike (trike) won't know it used...
  3. Replies
    5
    Views
    501

    Oh my lawd, I had forgotten about Dusty. Fuck...

    Oh my lawd, I had forgotten about Dusty. Fuck that guy.
    OP, this seems like a super fishy idea. Why not do something good instead and just donate all the money to me? I want more bikes and loads...
  4. Replies
    27
    Views
    5,969

    A lot.

    A lot.
  5. Replies
    18
    Views
    881

    Picture 2 is definitely not part of the neck....

    Picture 2 is definitely not part of the neck. That's a race in there, where the neck cup should sit. That's why it won't go in.

    Wait for the experts to weigh in, this is just my opinion.
  6. Replies
    18
    Views
    881

    You have bearing races in there? That's what the...

    You have bearing races in there? That's what the 2nd picture looks like. Get them out. Cut them carefully, or try tapping them out from the opposite side.
  7. Replies
    3
    Views
    513

    There are so many different versions of Sportster...

    There are so many different versions of Sportster forward controls, we're going to need pictures to help you figure this out. Most of them are shafts simply threaded/bolted into the motor mount, some...
  8. Replies
    18
    Views
    881

    Ironheads use a 7/8" steering stem and the...

    Ironheads use a 7/8" steering stem and the bearings and cups are thus smaller than on a Big Twin, which has a 1" neck stem.
    There are conversion bearings and cups out there to run a Big Twin front...
  9. Replies
    39
    Views
    1,857

    Dual lights always look good with longer forks,...

    Dual lights always look good with longer forks, niiiiiice.
  10. Thread: Newb + ?

    by Down
    Replies
    9
    Views
    507

    I like the way an Ironhead tickles my butthole

    I like the way an Ironhead tickles my butthole
  11. Replies
    3
    Views
    308

    Yes

    Yes
  12. Replies
    13
    Views
    863

    The frame is under tension. What happens when you...

    The frame is under tension. What happens when you cut it, is the freed tension pulls the frame rails apart. Just use ratchet straps to pull it back together and bolt your motor up.

    You need to...
  13. Thread: Biker Memes 2.0

    by Down
    Replies
    23
    Views
    2,675

    https://i.ibb.co/HHJWnBP/Screenshot-20211001-11040...

    https://i.ibb.co/HHJWnBP/Screenshot-20211001-110405.jpg
  14. Replies
    20
    Views
    1,360

    I love the lines of that. Classic skinny chop....

    I love the lines of that. Classic skinny chop. Good job, man!
  15. Did you ever get this project started? I'm...

    Did you ever get this project started? I'm looking at doing the same. Duo Glide frames seem to be widely available from Germany (I'm in Finland) and I'm looking at a late Shovelhead that comes with...
  16. Replies
    39
    Views
    1,857

    I've seen this on reddit, super cool bike! I like...

    I've seen this on reddit, super cool bike! I like it in all its goofiness. That fairing just sends it over the top and I'm all about that.
  17. Replies
    38
    Views
    2,682

    Thank you! I'm really stoked on how good the lens...

    Thank you! I'm really stoked on how good the lens came out, this was my second try. First one I cracked because I wasn't careful enough removing it from the build plate.





    I'm in need of a...
  18. Replies
    38
    Views
    2,682

    Made a tail light! Designed and manufactured by...

    Made a tail light! Designed and manufactured by me with the help of my pops.
    Might do a limited run of these, I like the way it looks. Still need to come up with the actual lights to put in, but I'm...
  19. Thread: Thank you!

    by Down
    Replies
    15
    Views
    2,298

    Sticky: Thank you for keeping this site going. It's a...

    Thank you for keeping this site going. It's a national treasure.
  20. Replies
    38
    Views
    2,682

    Progress has been slow lately. Missing some...

    Progress has been slow lately. Missing some important parts like oil bag, rear fender and exhaust.
    Trying to do the small stuff until I can afford to buy parts. Dog got sick, had to use my bike...
  21. Replies
    26
    Views
    1,543

    Welcome! Order of business sounds about right,...

    Welcome!
    Order of business sounds about right, there really isn't a right or wrong. Have fun, that's the most important part of building a bike that many people forget.
  22. Replies
    7
    Views
    530

    My brother had one of those on his Sportster. +2...

    My brother had one of those on his Sportster. +2 I think it was. Never complained about it. He liked the ride and said the quality on that thing was good. He only sold it to help finance a narrow...
  23. Replies
    17
    Views
    699

    Was just about to ask the same thing. You...

    Was just about to ask the same thing. You definitely need to run a ground wire to the bars ASAP if you don't have one. Otherwise you run the risk of welding your neck bearings and that is not good.
  24. Replies
    12
    Views
    660

    This one I really regret selling. 35 degree...

    This one I really regret selling.
    35 degree rake, Wide Glide trees and 6" over tubes with a 21" wheel.
    https://i.ibb.co/C6DbBJG/IMG-20190522-135820-109.jpg
  25. Replies
    12
    Views
    660

    He wants it to be a stock rake jacked up long...

    He wants it to be a stock rake jacked up long fork bike. Your (or mine for that matter) opinion doesn't matter here, it's his bike and he asked how it can look like the bike he wants it to look like....
Results 1 to 25 of 244
Page 1 of 10 1 2 3 4

Log in

Log in