PDA

View Full Version : 1977 kz650c build



ragecage
02-06-2015, 1:17 PM
Picked up this kinda running 77 kz. Its currently being worked over with basically all new parts.
Hopefully it will carry me around before summer.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/2015-01-17%2015.04.00.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/2015-01-17%2015.04.00.jpg.html)

ragecage
02-06-2015, 1:19 PM
No spark on two cylinders and weak spark on the other two. New coils, plugs, and wires getting installed this weekend.
Then get her idling to warm up and do compression check, check valve clearances, and probably disassemble/clean out carbs.

ragecage
02-06-2015, 11:05 PM
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150119_135018.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150119_135018.jpg.html)

Here's a better picture. It won't look anything like this when it's done but i guess this will be my "before" pic.

chekker45
02-06-2015, 11:32 PM
so what do plan to do with the bike

ragecage
02-07-2015, 1:14 PM
Lots haha.
brat style.
Stubby rear fender and loop the rear shock mounts. Solo seat. Replace rear struts with shocks. New exhaust. Engine Refresh (new gaskets, ignition). Put front forks back on(they are on backwards?)and rebuild front forks. Probably new bars. Going to hold off on paint till after summer. Hope to be posting pics of the progress.

ragecage
02-07-2015, 3:47 PM
Switching to a single speedometer gauge and rewire everything. I have sidecovers too. Prob see how it looks with them after the wiring is done.

ragecage
02-08-2015, 2:16 AM
Worked on the bike some today. My friend, Tyler, installed the new coils, wires, and plugs. And of course the battery was dead So didn't get a chance to fire it up. He also cut off that trailer fender that looked terrible.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150207_174504.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150207_174504.jpg.html)

Also reinstalled the rear shocks and messed around with a section of rear frame that the previous owner cut off. Hoping to use it as a short rear loop. Still have to de tab it and weld it on.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150207_203441.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150207_203441.jpg.html)

New clutch cable goin on too. Pretty grimey in there.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150207_201855.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150207_201855.jpg.html)

ragecage
02-08-2015, 2:22 AM
This wiring looks like a nightmare.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150207_174521.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150207_174521.jpg.html)

We were about to do all the brake pads/new brake fluid and bleed but one of the front calipers has a bolt instead of a bleeder screw so we had to hold off.

ragecage
02-08-2015, 12:05 PM
Wanting to move the battery mount to the underside of the seat rails and go with a slightly smaller battery. Any suggestions on a battery? Would love something more on the maintenance free side.

killmoretrout
02-08-2015, 12:58 PM
Wanting to move the battery mount to the underside of the seat rails and go with a slightly smaller battery. Any suggestions on a battery? Would love something more on the maintenance free side.

Curious what you find. We're gonna go with a smaller antigravity battery when the time comes. Something like -> this (http://www.dimecitycycles.com/9-7-amp-hour-240-cca-antigravity-8-cell-battery.html). When you figure out what you're gonna go with, post it here. Cheers, dude.

ragecage
02-08-2015, 2:06 PM
That battety looks really nice but a bit more than i would like to pay. Esp. if i need to buy a special charger for it as well.

ragecage
02-19-2015, 2:23 AM
Update!
My friend Tyler finally got his new shop all moved, so work commences....
Wiring harness was too buggered up. Redoing the whole thing. Moving all the handlebar controls to under the seat. New throttle tube assembly coming. Got antsy and put one grip on.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150218_145604.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150218_145604.jpg.html)

Profile of rear hoop.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150218_145650.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150218_145650.jpg.html)

It has a newer regulator/rectifier so thatll be reused but new starter solenoid, starter switch, points and condenser will go on.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150218_162043.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150218_162043.jpg.html)

ragecage
02-19-2015, 2:32 AM
Heres Tyler, putting the bike up after taking off the header tubes.
Gettin ready to flip the forks around the correct way. Then the brakes can get worked out.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150218_162156.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150218_162156.jpg.html)

deathmetaldan
02-19-2015, 5:35 AM
from the looks of things the previous owner was clueless..... imo you should probably dig around as much as possible and make sure more retardation isnt hiding in bad areas.

ragecage
02-19-2015, 11:36 AM
Don't worry. It is getting fully worked over. just had some lazy mods on it when i got it. Previous owner was trying to do a hack job of making a bobber.

ragecage
03-08-2015, 12:40 AM
i have been collecting parts for a while. Should have everything i need to put it back together by the end of next week. Pics will follow soon. The weather here is finally warming up so im getting hyped to get this thing going.

Sabai
03-08-2015, 9:00 AM
if the spark is still the same, set your points...

put the left hand cyclinder top dead center using alignment marks if it has them, turn the plate to it's mark if it has one, find something the thickness of a match book cover stick it between the point gap adjust til the cover can gently slide between them.

ragecage
03-09-2015, 7:59 PM
Tyler got the calipers all cleaned up.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/Photo02222126.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/Photo02222126.jpg.html)

Wire came in the post so Tyler got started with that while i started cleaning stuff off. Also received new stainless allen bolts for motor covers.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/IMG_20150309_154241.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/IMG_20150309_154241.jpg.html)

Before. Under sprocket cover.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150207_201855.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150207_201855.jpg.html)

After.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150309_190654.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150309_190654.jpg.html)

Also got the carbs off to look over. Going to clean up the motor some more.

ragecage
03-17-2015, 2:59 AM
Waiting...waiting on parts.
Yesterday took the forks apart to clean up and replace seals. the allen bolt on the bottom of one of the fork tubes just spins. Anyone have any idea how to get it apart? If not, i guess i need to find another right fork tube :(
heres how she sits now...
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150315_193235.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150315_193235.jpg.html)

Also spent a couple hours on the wire wheel cleaning these up for paint.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150316_173221.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150316_173221.jpg.html)

Going to start painting parts now that the weather has been nice.
Hope to have more stuff in by friday. Waiting on a speedometer from Australia. And some rubber stuff from the UK.

deathmetaldan
03-19-2015, 12:17 AM
Is the socket for the allen wrench deep enough to get a left handed drill bit or easy out in it? If so, put some heat on it and turn it out slowly.

if the socket isnt deep enough, try to drill it out a bit.... again, slowly.

ragecage
03-19-2015, 1:39 AM
Tyler used some moto magic and got it out.
Everything should start to pick up speed now that we have most everything for the build.

ragecage
03-22-2015, 2:57 AM
Spent a few hours sanding the frame for paint. Still some tabs to remove and weld the rear hoop. Then on to paint and reassembly.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150321_211506.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150321_211506.jpg.html)

Tyler gettin a sweet honda dream up and cruisin. He's flippin me the bird but it was kinda limp cause he was focused on the bike Haha.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150321_211708.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150321_211708.jpg.html)

If you're in kansas city and need some work done, call him up. Rare form motorcycles. He just made a fb page for his shop.

ragecage
03-25-2015, 11:32 AM
Went and worked on the bike on monday. Got started cleaning off all the unneeded tabs from the frame.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150323_184812.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150323_184812.jpg.html)

Tyler got the rear hoop section all cleaned off.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150323_191205.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150323_191205.jpg.html)

All the tabs taken off and hoop kinda fitted. Still needs to be adjusted a little Before it gets welded on. trying to figure out what to do with the battery tray. This is how she currently sits.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150323_192611.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150323_192611.jpg.html)

ragecage
03-25-2015, 11:40 AM
Todays plans:
harbor freight to pick up more blast media. Blast rear wheel.
Prep everything for paint.
rebuild front calipers.
reassemble front forks.
power wash engine block.
paint parts/frame.

ragecage
03-31-2015, 10:36 AM
Finished smoothing frame over. I small amount of bondo work still to do. Still need to power wash the motor then we can paint the frame and reassemble.

Some parts painted up.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150330_145220.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150330_145220.jpg.html)

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150330_192900.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150330_192900.jpg.html)

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150330_203754.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150330_203754.jpg.html)

Tyler testing his riding position on the cb chopper he's building. It's going to be pretty sweet.
[/URL]http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150330_210123.jpg

Forks are rebuilt.
[URL=http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150330_223011.jpg.html]http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150330_223011.jpg (http://s1144.photobuc[URL=http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150330_203754.jpg.html)

ragecage
04-04-2015, 9:15 PM
Rear hoop is welded on and also boxed in the frame where the shocks mount. Still have to smooth it out with bondo.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150329_120700.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150329_120700.jpg.html)

Getting closer.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150331_134625.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150331_134625.jpg.html)

ragecage
04-11-2015, 9:44 PM
Started in with the body filler. Fuzzy frame!
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150411_162305.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150411_162305.jpg.html)

After hours of grating and sanding. Going to do one more pass to fill the spots that we missed and then the final sand before paint.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150411_185835.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150411_185835.jpg.html)

Picked up the sheet metal for the seat pan. Set the tank on to get an idea of what its going to look like. Still need to fill the badge spots on the tank and sand it down smooth. Im going to do something fun with the tank paint.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150411_191151.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150411_191151.jpg.html)

ragecage
04-17-2015, 11:51 AM
Tires are mounted. Mocked up the rear to find fender placement.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150414_173218.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150414_173218.jpg.html)

Final filling and sanding on frame. We werent going to remove the motor to paint the frame but since its this far taken down we might as well. So tomorrow, hopefully, we will prime and paint the frame.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150414_220544.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150414_220544.jpg.html)

billybiltit
04-17-2015, 1:19 PM
moving right along!
keep us posted,

leon

PaulontheRun
04-17-2015, 1:33 PM
Digging it.

ragecage
04-19-2015, 1:37 AM
Had to put the rear wheel and hub back together to get the correct placement for the fender. Tail light is just sitting on there. We cant seem to get the rear tire to fully seat the bead. One section wont slide up the to the edge of the rim fully. Its like 2 mm off. Spent a lot of time trying different tricks to get it seated. no luck. Probably need some proper tire lube.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150418_210515.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150418_210515.jpg.html)

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150418_211711.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150418_211711.jpg.html)

ComestoLife
04-19-2015, 6:03 AM
Looks good. If you arent worried about it, I would ditch the kick starter and wire the bike with a capacitor if you want to go with something thats hard to see. Would have to make sure that your charging system is tip top though. But if you are planning on keeping the side covers (my opinion is that side covers are awesome and look great when they are painted nice, and a lot of bikes look like shit without em, unless the frame's metal work is good) then the battery size wont matter because it is covered up. Either way, keep posting lots of pictures, I really like these bikes and good luck with the build. Spend some money on good quality mufflers, when the time comes.

ragecage
04-19-2015, 10:51 PM
The frame will be completely open. We are making a small panel that will attach to the side of the battery tray for the switches So hopefully it will hide most of the wiring and starter solenoid and stuff.
I kinda like the kickstart so its staying.
Once the brackets for the fender are done, we should be able to paint.
Thats the only thing holding back the build right now.
I'll post as many pics as i can. Haha i love seeing threads with lots of pics too.

ragecage
05-05-2015, 10:55 AM
Fender tabs welded on now. Took the motor off the frame. Motor is all cleaned up.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150504_171346.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150504_171346.jpg.html)

Frame is ready for paint now. Hope to have ready by saturday and start reassembly.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150504_171330.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150504_171330.jpg.html)

Oyamum
05-07-2015, 2:22 PM
Awesome work mate, can't wait to see it finished.

ragecage
05-14-2015, 1:08 PM
Frame is primered. Next photos should be painted.

bluesrock
05-14-2015, 10:28 PM
Keep up the great work!

What did you use to get the engine so clean like that?

ragecage
05-15-2015, 12:33 PM
The area where the front sprocket is took a long time, brake cleaner and a wire brush. Then sprayed it down with simple green and let it sit for a bit, then power washed it. Went to a local rubber manufacturer and got rubber lab stoppers to plug all the holes up Before washing.

ragecage
05-31-2015, 12:16 AM
Got a good amount of work done today. Here come the pics.

Frame all painted up.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150530_154239.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150530_154239.jpg.html)

ragecage
05-31-2015, 12:17 AM
About to marry the motor and frame. Such a lovely ceremony.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150530_184917.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150530_184917.jpg.html)

ragecage
05-31-2015, 12:22 AM
Motor is in. Lets start getting her together!
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150530_204248.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150530_204248.jpg.html)

ragecage
05-31-2015, 12:24 AM
Its back on its own two wheels!!
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150530_213702.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150530_213702.jpg.html)

ragecage
05-31-2015, 12:28 AM
How she sits at the end of the day.
Tank still needs to be stripped and painted but heres a general idea of how it will look.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150530_232334.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150530_232334.jpg.html)

ragecage
06-01-2015, 7:51 PM
Aircraft stripper!
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150601_185318.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150601_185318.jpg.html)

ragecage
06-01-2015, 7:55 PM
Prime time.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150601_193719.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150601_193719.jpg.html)

billybiltit
06-02-2015, 9:00 AM
i really like the look you got going here.:cheersmate:

leon

ragecage
06-02-2015, 5:21 PM
Cut out the seat pan.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150601_231602-1.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150601_231602-1.jpg.html)

ragecage
06-09-2015, 1:40 AM
Tank sanded bare.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150608_172432.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150608_172432.jpg.html)

ragecage
06-09-2015, 1:43 AM
Fillin the lows and sanding till my life ends.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150608_223543.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150608_223543.jpg.html)

ragecage
06-18-2015, 1:05 PM
Got the tank all sanded smooth and sprayed with a high fill primer. Still need to wet sand and check the smoothness again.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150616_202335.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150616_202335.jpg.html)

ragecage
07-12-2015, 1:15 AM
Hope to begin building the new wiring harness on monday.

ragecage
07-18-2015, 3:44 PM
Currently.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150622_212024.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150622_212024.jpg.html)

ragecage
08-11-2015, 10:52 PM
Some small thing done yesterday.
Brakes are reassembled. Both front and rear brake pads i ordered do not fit the calipers (yes, i made sure i was ordering the correct ones). So ordered from a different vendor this time.
Clutch inspected.
Still need to pick up one valve shim to finish the valve job.
Began running the wiring for the new loom.

ragecage
09-09-2015, 1:09 PM
Valve job done, all covers put back on.
Now to finish wire loom, seat upholtered, tank paint, tune and ride.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/IMG_20150909_013124.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/IMG_20150909_013124.jpg.html)

ragecage
09-15-2015, 1:25 PM
Got a bit more small stuff put on yesterday. Throttle cables installed, began making a bracket to move the speedo down between the headlight and bars (looked off where it was before). Mounted the tail light.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150914_193229.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150914_193229.jpg.html)

ragecage
09-15-2015, 1:31 PM
Also threw the new exhaust on to check clearances, looks great. I may get a muff for it later on, but for now, straight dump. This is where we're at now.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150914_204903.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150914_204903.jpg.html)
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150914_205056.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150914_205056.jpg.html)
Tyler finished fabbing the plate for all the controls. Still needs to be welded to the battery box so no pics of that yet.

ragecage
10-12-2015, 8:12 PM
Cut out a new seatpan out of 20g steel and bent it to fit the rails. The other one was too thin.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150926_192846_RichtoneHDR.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150926_192846_RichtoneHDR.jpg.html)

ragecage
10-12-2015, 8:14 PM
Tyler started running the wires for the new harness. I dont know much about the electricals so im going to let him do that jam.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20150926_201901_RichtoneHDR.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20150926_201901_RichtoneHDR.jpg.html)

ragecage
02-28-2016, 1:32 AM
Finally warmed up for a few days so i could get some paint going. Still need to wetsand and clear it.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160227_235439.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160227_235439.jpg.html)

ragecage
04-25-2016, 2:48 PM
Tank is clear coated now. Used spraymax 2k clear. Wetsanded with 1500 and 2000 grit. Washed all off before i start polishing.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160425_154637.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160425_154637.jpg.html)

ragecage
04-25-2016, 2:49 PM
Bike is pretty much all wired now too. Waiting on a new brake light switch.

ragecage
04-25-2016, 4:56 PM
Polished and waxed. Not too bad for my first rattlecan job.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160425_165639.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160425_165639.jpg.html)

ragecage
07-26-2016, 2:28 AM
Repainted the tank badges.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160718_155058.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160718_155058.jpg.html)

ragecage
07-26-2016, 2:33 AM
Picked up my seat from a local auto upholstery shop. Looks great.
http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/IMG_20160722_161107287.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/IMG_20160722_161107287.jpg.html)

sooner7nc
08-04-2016, 6:52 PM
Great build. Tank looks good. I'd call it "Jailbreak"

jonbeavers0
08-07-2016, 8:45 PM
You run in to any issues with parts i have a 76 cant really find anything

ragecage
08-08-2016, 12:40 PM
Bike assembled. Still need to sleeve the wire harness.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160729_203857.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160729_203857.jpg.html)

ragecage
08-08-2016, 12:43 PM
Most everything done. Now time for tuning.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160805_132246.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160805_132246.jpg.html)

ragecage
08-08-2016, 12:46 PM
Tyler's cb750 chop and my bike.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160805_132255.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160805_132255.jpg.html)

ragecage
08-08-2016, 12:49 PM
Bikes at the art show/moto meet. Art made by S.R. Sadler. Really cool stuff.

http://i1144.photobucket.com/albums/o495/nickmuenz/Mobile%20Uploads/20160805_235745.jpg (http://s1144.photobucket.com/user/nickmuenz/media/Mobile%20Uploads/20160805_235745.jpg.html)

billybiltit
08-09-2016, 7:01 AM
the bike turned out really cool you done a good job .
the 750 is just the right kind of wild lookin!

leon

ragecage
06-26-2017, 1:12 PM
http://i1144.photobucket.com/albums/o495/nickmuenz/IMG_20170622_115059_682.jpg (http://s1144.photobucket./user/nickmuenz/media/IMG_20170622_115059_682.jpg.html)

Finally got time to get this thing moving again. Had an issue with a leaking oilpan. New gasket and we are good to go. Tyler and I got the bike started. Sounds great.
https://youtu.be/T_OdFy1CcDk

Just have to wrap up a few loose ends and I'll be riding.